Building a Birdhouse from Scrap Cedar (aka … SubTitle :: Do It Yourself with a Friend is Twice as Nice)
Yesterday, I told you a little bit about how I ended up here. In this post, I work with Beth of Beth’s DIY Workshop to build a birdhouse from scrap cedar. This birdhouse being my gift in a White Elephant Gift Exchange for this year’s Baltimore Bloggers Holiday Party hosted by One Project Closer.
Note: You may click any image. When the lightbox pops up, you may page through the entire gallery of images using the forward or back arrows. Enjoy.
This is What
I We Did: Building a Birdhouse Building Moxie Style
So … the birdhouse. I toke this stack or rough milled cedar scrap (white cedar, I believe). It had been cut, a few years ago, from the arches of our cedar fence (there is a great tutorial there one day). I also grabbed some leftover cedar shakes (from my previous house) and headed up to Beth’s.
This birdhouse, which has survived the renovations around the homestead … so far, and is still mounted to our shed, acted as inspiration. After thinking for awhile about roof design, it occurred to me I wouldn’t have to deal with roof framing, or funky cuts, if I just built a box and just flipped it on … a diagonal.
* At Beth’s, I started by squaring the ends up, creating equal lengths. For this, I used the shop’s sliding compound miter saw.
* We then took the ¾ inch boards (around 11” inch in length) and ran them through the table planer. Taking a 1/16th of an inch off of each side, this gave us 5/8th inch stock to work with. Running these across the table planer was much nicer than running through my budget table saw at home, and was way more accurate … I assure you. (As with most of the tools in the shop, Beth demonstrated and I finished. The only exception to this really – the dress press a little ways below, which Beth worked for me.)
* Taking the now planed boards, we ran them across the table saw with a dado set installed. We were making rabbets (notches) that were half the depth of the board (in this case 5/16”) – ½” from the edge. The idea being that when glued and lapped – two boards each making a side, could be nailed. Again, I have a dado kit at home, but I assure you this was much faster on Beth’s rig. With setup, this step, too, took about 15 minutes.
While we didn’t review plans, I was fortunate that Beth actually had a birdhouse, okay two, hanging in her shop. One was built, she told me, from a set of plans provided by the Sierra Club. Using that birdhouse, we determined both an appropriate depth for the birdhouse, plus the preferred size for the birdhouse front door. One and half inches in diameter.
* From there, we gang cut, in two passes, four boards at a time on the sliding miter saw. This yielded 16 planed and notched boards 5 1/2” long.
* Now, it was simply a matter of gluing and nailing this stock to create a box. (A class that Beth actually teaches at the Workshop.) We assembled all the sides using a pin nailer (like a pneumatic brad nailer only shooting smaller nails). Again, I don’t have one at home. They were a little long and we had to flip these boards over to snip off the ends poking through. No biggie, as we caught ourselves saying, well, a few times – “It’s only a birdhouse.” (Note the “split” in the pair of boards we used as a nailing surface. This kept the too long nails from nailing into anything.)
* We then assembled the box: gluing and weaving at each corner to make a perfectly square box. Here we used 1 ½” 16 gauge brad nails. Done in a jiffy.
* Next, I really wasn’t sure what I was going to do with the front. We in the end decided to run both sides of two longer pieces across the dado blades. This created two tees. These boards would act as the center “slats” for the front and the back of the birdhouse. Note: You could do this kind of notching on a table saw fitted with a standard blade, but here, it is just slightly more efficient with the dado blade.
I decided to set these boards vertically, diagonal to my diagonal box. I cut one end to a point by opposing two 45s at a center point. I then placed it (pictured: Beth doing one) lining up the point with the corner that I chose to eventually hide up under the roof. We scribed the bottom ends and made those cuts.
* Once (face) nailed into place, I used my remaining 5 1/2” pieces for “ears.” This revealed perhaps the one major flaw in my process and design here. These boards ended up being both a little too short and also exposed a joint (at the top) which water could maybe get into. Again – “Only a birdhouse” and they will be protected under eaves.
For the ears on the front, I scribed these too and made careful cuts … I mean – as not to saw off a finger. For the back, I made the impromptu decision not to cut the ears to the shape of the box. These ears I thought would make for good mounting surfaces if the new owner chooses to mount it flush somewhere. (This birdhouse could also be hung from a tree with a stainless eye-hook and some aluminum wire or something. Really it could be installed, in any number of other ways, fastened to something or hung.)
* From here, we needed both the birdhouse doorway and a hole for a dowel, which would accommodate a little perch. These holes we set roughly on center. We cut doorway hold on Beth’s drill press using a 1 ½ inch Forstner bit (Beth driving). Just below that we cut a 3/8” hole and found an old pool cue – placing it briefly on the stationary belt sander and cutting it to about 2 ½ inches long. This was then simply glued firmly into the hole. In this case, again, I do not have a dress press at home (and especially not one that is as sweet as Beth’s old school Craftsman). A drill press certainly makes as neat a hole as I could have made at home with my drill (understatement).
* Now time for the roof, and admittedly the least amount of thought went into this. I found four equally sized shakes and laid them, butted tightly together, onto the roof essentially determining what the overhang at the front would be. I then cut the four shake shingles on the shallow side. When cutting to length, I left about 1 ½ inch extra as to create equal overhangs all the way around the roof.
* In the final steps, my sugar was starting to dip. And as I still planned to tour Beth’s upstairs, this revealed perhaps my few flaws in execution. I then cut the thick side of previously used shingles; two to 2 inches and two to 1 5/8”. I did this to account for overlapping or weaving. I then glued the back side of each and the edges of these and slapped them together to create a sorta ridge shingle. I split these when I set them so that they would not fall directly over the seam at the first course of shingles and also to create a more effective overhang at the front.
I then filled in with slightly longer slivers (cut from another shingle) to provide both a stagger and coverage at the seam and to give the roof a slight visual variation.
* Here, I was a little sloppy with the glue and some squeezed out leaving a little staining on the roof… “Only a Birdhouse.” In the final minutes, a grabbed a scrap piece of Poplar in the shop and trimmed out the exposed edge of the roof.
* And there it is. Building Moxie‘s Birdhouse #1.
There is something simply sublime about working with cedar. The smell is just glorious and cedar makes for a near-perfect exterior wood. While I think most would be tempted to treat it … in this application, I think I’d want to check how to see what the prevailing knowledge is. How do birds feel about stain and/or paint? For now, and as a gift – it remains as is.
All that in a few hours at a local DIY Workshop. It was fun: it was fun doing a creative project (for once), it was fun using tools other than my own, and it was fun DIYing with someone one else. …
Thanks to Beth, thanks to you and thanks, well, to the birds. Have a super day all. ~jb
About Building Moxie
BuildingMoxie.com is the do-it-together blog about house, home, and neighborhood (or 'hood for short), ... we feature a variety of topics written by, and for, both the diyer and the pro. ... Maybe you?
Hi & Welcome!
Find Building Moxie Also On:
- The Benefits of New Roofing :: GAF Roofing’s Website Makes It Easy Like a Click of the Heels
- The Scoop on Shovels :: A Visual Guide to Shovels
- Pro Tips and Tricks for Taking Out a Wall. Oh! & Removing a Pocket Door Too
- Raise the Roof 3 :: Video: Installing a Gutter (Half Round)
- Raise the Roof 2: Replacing Roof Flashing at a SideWall :: More with the Porch Progress
- Raise the Roof :: Jacking Up a Porch Roof :: Porch Progress and the Old House Effect
- Dig This! AMES Tools Built America. :: The Tool School Media Event
- April Showers Bring May … Projects :: Revisiting the Home Advisor Hangout: Spring Home Projects
- Baltimore’s Wild & Wonderful Hand Painted House Screens || Book: The Painted Screens of Baltimore
- Dear Spring: What Took You So Long? Signed, Winter :: 6 Common Winter Caused Spring Home Repairs from DoItYourself.com
About jb bartkowiak (321 posts)
A one-time construction manager, and always handyman, turned blogger and editor - Your Home Project Assistant. My wife, Jen, and I are on our 6th property (. . . yes, together). She is a real estate agent. We have two beautiful daughters Evyn and Eva. We currently live and are restoring an 1889 farmhouse in Baltimore's Lauraville area.